Mobile Gate Welding and Frame Repair
Steel and iron gates rarely wear out all at once. A weld cracks at a hinge, a bracket tears loose, a truck clips the frame or a storm drops a limb on it. Most of that can be repaired in place, on the gate, without starting over.
Open 24 hours, 7 days a week

What you might be seeing
Crack at a hinge or bracket weld
A hairline crack with rust bleeding out of it grows a little every time the gate moves. Caught early, it is usually a simple re-weld.
Frame bent after a vehicle hit
Even a slow bump from a truck or trailer can bow a frame enough that the gate binds, drags or will not latch.
Opener bracket pulling away
The arm bracket takes a push and a pull on every cycle. When its weld or bolts fail, the gate stops where it likes and the opener takes a beating.
Gate out of square
One corner drops, one side rubs and the gate looks crooked. A broken crossbar or diagonal brace is often the reason.
Pickets loose, missing or broken
Ornamental gates lose pickets to impacts, rust or a failed weld where the picket meets the rail.
Rust eating through the tubing
Bottom rails and joints where water collects rust first. Left long enough, the steel loses its strength.
Why gate welding happens on site
A driveway gate can weigh several hundred pounds, and taking it down to haul away is a job in itself. With mobile welding equipment, most frame and hardware repairs happen right at the post. We secure the gate, disconnect the opener, protect nearby surfaces and make the repair where the gate hangs. In a dry Texas summer, sparks and dry grass are a bad mix, so the area is cleared first.
Not every gate is a good candidate for welding. Thin, badly rusted tubing does not hold a weld well, and aluminum needs different equipment and care than steel. If a section should be replaced rather than patched, we will say so.
Frame repair after vehicle impact and storm damage
Impacts are one of the most common ways gates get hurt. A delivery van misjudges the turn, a trailer swings wide, someone backs out too fast. Storms are close behind in North Texas, where spring weather brings high wind and falling limbs. Either way the damage is rarely only what you can see. A bent leaf can also mean a sprung hinge, a cracked post weld and an opener that was shoved past its limits.
We check the whole gate before deciding what to fix. Bent frames can often be straightened. Kinked tubing, crushed rails and torn sections are cut out and replaced with new steel welded in, then ground and painted.
- Broken frame repair and bent frame straightening
- Crossbar, rail and picket replacement
- Panel replacement on ornamental and steel gates
- Vehicle impact repair and storm damage repair
- Reinforcement welding on frames that flex or rack
Bracket, hinge and track welding
Much gate welding is on the parts that tie the gate to its hardware. Opener brackets, hinge mounts, chain and roller brackets on slide gates, and track sections all take repeated load, and they are the usual places for welds to crack.
- Hinge welding and new weld-on hinges
- Support bracket welding and operator bracket fabrication
- Chain bracket and roller bracket welding on slide gates
- Track welding and repair of broken track sections
- Latch and lock mount repair
Iron, steel and aluminum gates
Ornamental iron and steel are the gates we weld most often around Denton County, from scrolled iron at homes near the lakes to tube steel and pipe gates on acreage. Aluminum gates turn up in newer subdivisions. They are lighter and do not rust, but they crack differently and need the right process. Tell us what your gate is made of, or send a picture with the request form, and we can tell you whether it can be repaired in place.
Rust repair, corrosion treatment and repainting
A weld is only part of the job. Bare steel left unpainted starts to rust quickly in humid weather. We clean back to sound metal, treat the area, then prime and paint it to match as closely as practical. On a gate with rust in several places, we can talk about a broader corrosion treatment and repainting so the next weak spot is not already forming.
Pricing for welding work
Welding jobs range from one bracket to a rebuilt frame, so call for pricing on your gate. Ask about current discounts when you call.
Quick checks from the driveway
- Look along the frame for cracks, especially at the hinges and the opener bracket
- Sight down the top rail to see whether it is bowed or twisted
- Check whether the gate still clears the drive along its whole path
- Take pictures of any impact or storm damage before anything is moved
- Turn the opener off if the gate is bent or binding
Stay clear while it misbehaves
Do not run an opener on a gate that is bent, cracked at a hinge or binding. It can bend further, tear loose or fall. Turn the opener off, keep people and animals out of its path, and stay clear of sharp, torn metal.
Questions people ask us
Do you weld on site or take the gate to a shop?
Most repairs are done on site with mobile welding equipment. A gate that needs extensive rebuilding is a different conversation, and we will explain the options.
Can a gate that was hit by a car be repaired?
Often, yes. Bent sections can be straightened or replaced, and the hinges, posts and opener are checked too, because impact damage spreads.
Can you weld an aluminum gate?
Tell us when you call. Aluminum needs a different process than steel, and whether it can be repaired in place depends on the gate and the damage.
Will the repair match the rest of the gate?
Welds are ground smooth where it matters, and repaired areas are primed and painted to match as closely as practical. An older finish may look slightly different until the whole gate is repainted.
What does gate welding cost?
It depends on the material, the number of repairs and whether new steel is needed. Call (940) 240-2402 for pricing on your gate and ask about current discounts.
Other gate work we do
Gate Welding & Frame Repair in Denton County: call any hour
We pick up 24 hours, 7 days a week. Call for pricing on your gate. Ask about current discounts when you call.