Skip to content
DentonGate Repair

Gate Opener Installation and New Automatic Gates

Whether you have a manual gate you are tired of stopping to open by hand, an old opener that has run its course, or a new property with no gate at all, the work starts with one question: what does this gate need to do every day?

Open 24 hours, 7 days a week

Black iron automatic swing gate partly open across the driveway of a brick two-story home

What you might be seeing

Planning a gate opener installation

We start with the gate, the ground and the way you use the entrance. That means the length, weight and material of the gate, which way it swings or how much room it has to slide, the slope of the drive, how many times a day it runs, where power is available, and how you want to open it: remotes, a keypad at the road, or an exit loop or sensor for cars leaving.

Those answers decide whether a linear arm, an articulated arm, a pad-mounted slide operator or a cantilever setup fits, and what size of operator the gate needs. Undersizing to save on the first purchase is one of the most common reasons an opener fails early.

Manual to automatic gate conversion

Most sound swing and slide gates can be automated, but the gate has to move freely first. We check the posts, hinges, wheels and frame, and fix anything that binds before an opener goes on. A gate that is hard to push by hand will be hard on any motor.

  • Automatic swing gate opener installation, single or dual
  • Automatic sliding gate opener installation and cantilever setups
  • Mounting brackets, concrete operator pads and post reinforcement
  • Photo eyes, safety edges and warning signs fitted as part of the install
  • Exit loops or vehicle sensors, plus keypads and remotes to open the gate
  • Battery backup so the gate keeps working through an outage

Ranch entrance and long-driveway automation

On acreage, the entrance can sit a long way from the house, past pasture or a creek crossing, with no power anywhere near it. Solar openers are common out here, paired with a battery sized for how often the gate runs and how many cloudy days it has to ride through. Where power is close, a low-voltage run from a transformer can work instead.

Long pipe gates need an operator and bracket built for the length and for wind, hinge posts that will not lean, and a plan for livestock. We set the gate so it holds firmly closed, and we think through where sensors go so animals standing in the opening are protected too. For problems with a solar opener you already have, see our ranch gate opener repair page.

New driveway gate installation

If there is no gate yet, the gate, posts and opener can go in as one job. That includes swing, sliding and cantilever driveway gates, pedestrian gates beside the drive, and ranch and farm entrance gates. Posts get footings sized for the gate, slide gates get a proper concrete track or channel, and conduit is trenched for the low-voltage wiring.

Lake-area homes often have sloped drives, and newer subdivisions often have HOA design rules. Both are worth checking before you choose a gate style. If your HOA has written guidelines, have them handy when you call.

  • Residential driveway gate installation: swing, sliding or cantilever
  • Pedestrian gate installation
  • Ranch entrance and farm gate installation
  • Concrete footings, slide gate channels and operator pads
  • Underground conduit trenching for low-voltage wiring

Power and wiring

Most of what we run is low-voltage control and charging wire. If your installation needs a new high-voltage circuit from the panel, a licensed electrician handles that circuit, and we coordinate the opener side of the job with them.

Installation pricing

Adding an opener to a sound gate and putting in a new gate with posts, concrete and solar are very different jobs. Call for pricing on your gate, and ask about current discounts when you call.

Quick checks from the driveway

  • Measure the gate length and note what it is made of
  • Push the gate by hand to see whether it moves freely
  • Note where the nearest outlet or breaker is
  • Look at which way the gate swings and whether the drive slopes
  • Think about how many people and vehicles use the gate each day

Stay clear while it misbehaves

An automatic gate is a heavy machine. A good install includes photo eyes or edges, correct force settings and warning signs so the gate does not close on people, pets or livestock. Until a new opener has been installed and tested, keep working the gate by hand.

Questions people ask us

Can my existing manual gate be automated?

Usually, if it is sound and moves freely. We check the posts and hinges first and fix anything that binds before mounting an opener.

Do I need power at the gate?

No. Solar openers suit many ranch and long-driveway entrances. Where power is close, a low-voltage transformer can be used. New high-voltage circuits are run by a licensed electrician.

Should I choose a swing gate or a slide gate?

It depends on space and slope. Swing gates need room to open and struggle on uphill drives. Slide gates need room along the fence. We walk the site and talk through the options.

Can you install a gate in a new subdivision?

Yes, though many HOAs have design rules. Check them first and share them with us when you call.

How much does gate opener installation cost?

It depends on the gate, the operator size, the power source, any concrete work and the accessories you want. Call (940) 240-2402 for pricing on your gate and ask about current discounts.

Other gate work we do

Gate Opener Installation in Denton County: call any hour

We pick up 24 hours, 7 days a week. Call for pricing on your gate. Ask about current discounts when you call.

Call nowGet a quote