Gate Safety Sensor, Photo Eye and Vehicle Loop Repair
Sensors and loops are how an automatic gate knows a car is waiting, a car has passed, or something is in the way. When one fails, the gate either refuses to move or moves when it should not, and both are worth fixing quickly.
Open 24 hours, 7 days a week

What you might be seeing
Stops and reverses for no reason
A dirty, misaligned or failing photo eye, or a safety edge that has been crushed or has a broken wire, tells the opener something is in the way.
Opens but will not close
Most openers refuse to close while any safety input is active. One blocked or faulty eye is enough to hold the gate open.
Opens by itself
An exit loop or loop detector that is stuck on, or a damaged loop wire, can send open commands with no car there.
Exit gate ignores cars
The free-exit loop or vehicle sensor is not detecting. Cracked pavement, a broken loop wire or a detector set too low are common causes.
Closes on a car still in the opening
The safety loop or shadow loop under the gate path is not holding the gate. Treat this one as urgent.
Fault light on the opener board
Many boards flag a sensor fault with a light or beep pattern. Note it before you reset anything.
Photo eye and safety edge repair
Photo eyes, also called infrared safety sensors, send a beam across the gate path. If something breaks the beam, the gate stops or reverses. Safety edges are rubber strips on the gate or post that sense contact. Both are entrapment protection, and both live outdoors through sun, dust, mud and wasp season.
Most photo eye trouble turns out to be alignment, dirt, a loose bracket or a wiring fault rather than a dead sensor. We clean and align the eyes, test the wiring back to the board, and replace sensors or edges that have failed. When an edge needs replacing, wired and wireless safety edges are both options.
- Photo eye installation, replacement, alignment and troubleshooting
- Safety edge installation and replacement, wired or wireless
- Obstruction sensor repair and reversing troubleshooting
- Adding sensors where a gate has too little entrapment protection
Exit loops, safety loops and loop detectors
A vehicle loop is a loop of wire cut into the driveway and sealed. A loop detector inside the opener reads the change when a car sits over it. A free-exit loop lets departing cars open the gate. A safety loop or shadow loop holds the gate open, or keeps it from moving, while a car is in its path.
Loops fail when the pavement around them moves. That makes them a real issue in Denton County, where clay soil heaves and shrinks, and in new subdivisions where drives are still settling. Cracks across the saw cut, tree roots, lawn edging and heavy trucks can all break a loop wire. We test the loop and the detector separately, adjust or reprogram detector sensitivity, and replace detectors that have failed.
When a loop is broken, we saw cut a new one, lay new wire, seal it and connect it to the detector. Where cutting the drive is not practical, such as pavers, gravel or caliche, an above-ground vehicle detector or a buried magnetic vehicle sensor can do a similar job.
- Underground exit loop installation, repair and replacement
- Loop detector replacement and programming
- Safety loop and shadow loop repair
- Vehicle presence sensors, above-ground detectors and magnetic vehicle sensors
- Loop saw cutting and sealing
Gate safety inspection
If you are not sure your gate has the protection it should, we can go over it with you. We check that photo eyes, edges and loops are placed and working the way the UL 325 and ASTM F2200 standards expect for a gate of its type, that the opener reverses when it should, and that warning signs are posted on both sides. Where protection is missing, we explain the upgrade options. This is a practical check of the safety devices, not a certification.
On horse properties and anywhere children play near the drive, it is worth asking where the sensors sit compared with where people and animals actually stand. A photo eye mounted at bumper height may miss a foal or a small child.
Pricing for sensor and loop work
Cleaning and realigning a photo eye and cutting a new loop are very different jobs. Call for pricing on your gate, and ask about current discounts when you call.
Quick checks from the driveway
- Wipe both photo eye lenses and clear grass, mud or webs between them
- Check that each eye still faces the other and its bracket is tight
- Look at the safety edge rubber for cuts, crushing or loose wires
- Walk the drive over the loop and look for new cracks across the saw cut
- Note whether the problem shows up in rain, in heat or at one time of day
Stay clear while it misbehaves
Never bypass, tape over or unplug a photo eye, edge or loop to make the gate close. Those devices are what stop the gate from closing on a person, a pet or a car. If the gate is closing when it should not, switch it off or leave it open until it is repaired.
Questions people ask us
Why does my gate reverse right before it closes?
Something is tripping a safety input near the end of travel: a photo eye catching low sun or slightly out of line, a safety edge brushing the post, or the opener sensing resistance from a dragging gate.
My gate opens by itself at night. What causes that?
A loop detector stuck on, a damaged exit loop or water in a wired button are common causes. We test each input to find the one sending the command.
Can a loop be fixed without cutting the drive again?
Sometimes the break is in the lead-in wire or the connection and can be repaired there. If the loop itself is broken in the pavement, a new cut is usually needed, or an above-ground sensor can be used instead.
Can you put an exit loop in a gravel driveway?
A cut loop needs pavement. On gravel or caliche we usually look at a buried magnetic sensor or an above-ground detector instead.
Does my gate meet UL 325?
We can check that the safety devices are present and working the way the standard expects for your gate type, and explain any gaps. That is a practical inspection, not a certification.
Other gate work we do
Safety Sensor & Loop Repair in Denton County: call any hour
We pick up 24 hours, 7 days a week. Call for pricing on your gate. Ask about current discounts when you call.